Teletronics EZPlatform Bedienungsanleitung

Teletronics EZPlatform™ AP/Hotspot/Repeater User Manual v1.2 © 2008 Teletronics International, Inc

10 To view details of the Linux operating system, the Linux kernel and network settings, click on the ‘View System Details’ button. The page in Figu

11 5.2.2. Wireless Status The Wireless Status page is shown in Figure 7. Figure 7. Wireless Status page The Wireless Status page displays curre

12 5.3. Network Settings 5.3.1. WAN The WAN page is shown in Figure 8. Figure 8. WAN page WAN Assignment WAN Interface: this setting allows y

13  ETH2: Ethernet port closer to the serial ports on the PCB.  WLAN1: Mini PCI slot closer to the Ethernet ports in the PCB, wired to the antenna

14 follow the instructions in the 'Dynamic DNS' section. Once you have set up the DDNS relation, obtain the DDNS certificate from the '

15 5.3.2. LAN The LAN page is shown in Figure 10. Figure 10. LAN page DHCP Server Enable DHCP server: whether the EZPlatform™ should act as DH

16 Alternate DNS server: the alternate DNS server that will be used in the configuration of DHCP clients. Lease time (min): the period of time the I

17 5.4. WLAN1 and WLAN2 WLAN1 and WLAN2 are the fixed designations for the two EZPlatform™ wireless interfaces. WLAN1 is the radio card closer to the

18 Basic Settings SSID: the service set identifier of the WLAN interface. An AP and an SU must have the same SSID to associate each other. Never as

19 5.4.2. Security The Security page is shown in Figure 12. Figure 12. Security page Encryption Type Encryption type: select the encryption t

2 Table of Contents 1. Product Overview ...3 2. S

20 Authentication: select the WEP authentication type.  Open: stations are always automatically authenticated and associated, but cannot pass traffi

21 5.4.3. AP Settings The configuration in AP Settings will only be applied when the WLAN interface is being used in AP mode. If SU mode is used, the

22 not be used at the same time. When using WDS, all WDS stations must use the same channel and different SSIDs.  Enable  Disable AP MAC address 1-

23 5.4.4. SU Settings (WLAN1 only) Only WLAN1 has the ‘SU Settings’ secondary tab, since WLAN2 can only be operated in AP mode. The configuration in

24 5.4.5. Advanced The Advanced page is shown in Figure 15. Figure 15. Advanced page Advanced Fragmentation threshold (bytes): the maximum all

25 5.4.6. MAC Filtering The MAC Address Filtering page is shown in Figure 16. Figure 16. MAC Address Filtering page MAC Address Filtering MAC

26 Save: store the changes made on this page. Cancel: undo the changes made on this page.

27 5.5. Bandwidth Control Bandwidth control allows you to limit the rate at which devices can upload to or download from the EZPlatform™. The Bandwi

28 i.e. for devices whose MAC address does not appear in the table at the bottom of the page. Typically, you will want the default rates to be lower (

29 5.6. Administration 5.6.1. System Configuration The System Configuration page is shown in Figure 18. Figure 18. System Configuration page B

3 1. Product Overview Teletronics' EZPlatform™ AP/Hotspot/Repeater is designed for high-power access point, hotspot and repeater applications. A

30  Enable  Disable TELNET: enable or disable access to the web interface via Telecommunication Network.  Enable  Disable SNMP: enable or disabl

31 5.6.2. Admin IP Filter The Admin IP Filter page is shown in Figure 19. Figure 19. Admin IP filter page Administrator IP address filtering is

32 5.6.3. Password The Password page is shown in Figure 20. Figure 20. Admin IP filter page Password Current password: enter your current pass

33 5.6.4. Backup and Restore The Backup and Restore page is shown in Figure 21. Figure 21. Backup and Restore page System Backup Download conf

34 System Restore Reset all settings to default: click on this button to restore all the settings of the EZPlatform™ to factory default, including t

35 5.6.5. Firmware Upgrade The Firmware Upgrade page is shown in Figure 22. Figure 22. Firmware Upgrade page Firmware Upgrade Browse: click on

36 5.7. Log The Log page is shown in Figure 23. Figure 23. Log page This page shows you important events that have been logged by the EZPlatfor

37 5.8. Reboot The Reboot page is shown in Figure 24. Figure 24. Reboot page Reboot: clicking on this button reboots the EZPlatform™.

38 6. Console and TELNET Access If for any reason you cannot access the EZPlatform™ via the web interface, you may still be able to recover the unit

39 7. EZManager To help you administer your network easily and effectively, Teletronics offers free network administration software called EZManager,

4 2. Specifications Technical Information Standard compliance IEEE 802.3 10/100BASE-T with autonegotiation Bandwidth Control Mac address-based, s

40 8. Frequently Asked Questions 1. What is the default IP address, user name and password of the EZPlatform™?  IP address: 192.168.1.124  User n

41 If the access point or the subscriber unit does not appear in the Wireless Status page, follow these steps:  Test the radios at a close distance

5 3. Typical Network Configuration The wireless interfaces of the EZPlatform™ can be configured in a number of ways, each suited for a particular app

6 4. Hardware Setup and Status LEDs Hardware Setup Figure 1 shows how to connect the EZPlatform™. Figure 1. Network and power connections The

7 5. Web Interface Configuration The EZPlatform™ can be conveniently configured using its web interface. The web interface provides intuitive navigat

8 5.1. Login Information After properly connecting and powering the unit, wait for the unit to finish the boot-up process. On the computer connected

9 5.2. System Information 5.2.1. General The web interface is the home page and thus is the page displayed when you log in. This page displays a sum